acrylonitrile-butadiene-styrene pipes

  • 1Acrylonitrile butadiene styrene — Acrylonitrile butadiene styrene, or ABS, (chemical formula (C8H8· C4H6·C3H3N)n) is a common thermoplastic used to make light, rigid, molded products such as piping, musical instruments (most notably recorders and plastic clarinets), golf club… …

    Wikipedia

  • 2Styrene — Preferred IUPAC n …

    Wikipedia

  • 3industrial polymers, major — Introduction       chemical compounds used in the manufacture of synthetic industrial materials.       In the commercial production of plastics, elastomers, man made fibres, adhesives, and surface coatings, a tremendous variety of polymers are… …

    Universalium

  • 4Polystyrene — For other uses, see Polystyrene (disambiguation). Expanded polystyrene packaging …

    Wikipedia

  • 5Plastic — is the general common term for a wide range of synthetic or semisynthetic organic solid materials suitable for the manufacture of industrial products. Plastics are typically polymers of high molecular weight, and may contain other substances to… …

    Wikipedia

  • 6Cross-linked polyethylene — PEX redirects here. For other uses, see Pex (disambiguation). Cross linked polyethylene, commonly abbreviated PEX or XLPE, is a form of polyethylene with cross links. It is formed into tubing, and is used predominantly in hydronic radiant heating …

    Wikipedia

  • 7Plastic pipework — standards for the conveyance of drinking water,waste water, chemicals, heating and cooling fluids, foodstuffs, ultra pure liquids, slurries, gases, compressed air and vacuum system applications. Plastic Pressure Pipe Systems have many advantages… …

    Wikipedia

  • 8Poly(methyl methacrylate) — This article is about the transparent plastic sometimes called acrylic glass. For the glass/plastic laminate often called safety glass , see laminated glass. Poly(methyl methacrylate) …

    Wikipedia

  • 9Pipe (fluid conveyance) — For structural pipe, see Hollow structural section. For other uses, see Pipe (disambiguation). Steel pipes …

    Wikipedia

  • 10Pipe (material) — A pipe is a tube or hollow cylinder used to convey materials or as a structural component. The terms pipe and tube are almost interchangeable. A pipe is generally specified by the internal diameter (ID) whereas a tube is usually defined by the… …

    Wikipedia

  • 11Tap water — Indoor Tap commonly found in the bathroom or kitchen. This tap is a single handle, double spout tap (one spout for hot water, one spout for cold water). Tap water (running water, city water, municipal water, etc.) is a principal component of… …

    Wikipedia

  • 12Plastic pressure pipe systems — are used for the conveyance of drinking water, waste water, chemicals, heating and cooling fluids, foodstuffs, ultra pure liquids, slurries, gases, compressed air and vacuum system applications, both for above and below ground applications.… …

    Wikipedia

  • 13Piping and plumbing fittings — Fittings are used in pipe and plumbing systems to connect straight pipe or tubing sections, to adapt to different sizes or shapes, and to regulate fluid flow, for example. Fittings, especially noncommon types, can be expensive, and require time,… …

    Wikipedia

  • 14Spud gun (cannon) — This article is about pipe based cannons and similar which use air pressure, or combustion of a gaseous fuel, or both, to launch large projectiles at low speed. They are in two types: * To fire whole potatoes. These launchers are built and fired… …

    Wikipedia

  • 15Spud gun — For the child s toy which fires small pieces of potato, see spud gun (toy). A pneumatic potato cannon A potato cannon (also known as a spud gun or spudzooka ) is a pipe based cannon which uses air pressure (pneumatic), Propellant, or… …

    Wikipedia

  • 16plastic — plastically, plasticly, adv. /plas tik/, n. 1. Often, plastics. any of a group of synthetic or natural organic materials that may be shaped when soft and then hardened, including many types of resins, resinoids, polymers, cellulose derivatives,… …

    Universalium

  • 17Materials science — Simulation of the outside of the Space Shuttle as it heats up to over 1,500 °C (2,730 °F) during re entry into the Earth s atmosphere Materials science is an interdisciplinary field applying the properties of matter to various areas of… …

    Wikipedia

  • 18Injection molding — (British: moulding) is a manufacturing process for producing parts from both thermoplastic and thermosetting plastic materials. Molten plastic is injected at high pressure into a mold, which is the inverse of the product s shape. After a product… …

    Wikipedia

  • 19chemical industry — Introduction       complex of processes, operations, and organizations engaged in the manufacture of chemicals and their derivatives.       Although the chemical industry may be described simply as the industry that uses chemistry and… …

    Universalium

  • 20hydrocarbon — hydrocarbonaceous, adj. /huy dreuh kahr beuhn, huy dreuh kahr /, n. any of a class of compounds containing only hydrogen and carbon, as an alkane, methane, CH4, an alkene, ethylene, C2H4, an alkyne, acetylene, C2H2, or an aromatic compound,… …

    Universalium